Pasco TD-8556A STEAM GENERATOR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Pasco TD-8556A STEAM GENERATOR. PASCO TD-8556A STEAM GENERATOR User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 1
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Instruction Sheet
for the PASCO
Model TD-8556A
STEAM GENERATOR
012-04696D
5/01
$1.00
Introduction
The PASCO scientific Model TD-8556A Steam Genera-
tor is an efficient source of steam and hot water for the
student lab. The one liter stainless steel tank is electrically
heated with a variable output of up to 400 Watts. The dan-
gers of overheating are eliminated by the thermal circuit
breaker that disconnects the power if the water boils dry.
Operation
CAUTION:
The stainless steel tank gets HOT when the unit
is on.
DO NOT immerse the unit in water.
ALWAYS plug into a grounded receptacle. Do
not use a three-to-two-prong adaptor.
Operation is simple. Plug the unit into a standard 115/220
VAC, 50/60 Hz outlet. Fill the one liter tank approxi-
mately 1/2 to 3/4 full of water and place the rubber stop-
per over the top. Flip the ON/OFF switch to ON. The
switch will light to show that power is entering the unit.
Turn the power dial clockwise, and the heater will click
on. Set the dial to 8 if you want steam or boiling
water, to a lower setting if you want hot but not boiling
Phone (916) 786-3800 • FAX (916) 786-8905 • email: techsupp@PASCO.com
10101 Foothills Blvd. • P.O. Box 619011 • Roseville, CA 95678-9011 USA
better
teach science
ways to
© 1991 PASCO scientific
This instruction sheet written/edited by: Bruce Lee
Fill with water,
1/2 to 3/4 full.
To direct the output of
steam, attach 1/4-inch
inside diameter tubing. For
maximum output of steam,
block one opening.
water. At full power, it will take 10-15 minutes to bring
3/4 of a liter of water from room temperature to boiling.
A baster is provided for removing hot water from the tank
for use in experiments. If you need steam, attach plastic
tubing (1/4-inch inside diameter) to the tubes on the rubber
stopper—two experiments can be performed simultane-
ously. For the full steam output of approximately 10 grams/
minute, block the tubing on one side with a tubing clamp.
If the water in the tank runs low, the thermal circuit
breaker will cut off the power to the heater and the LOW
WATER light will come on. In this case, just add more
water to the tank. When the tank cools sufficiently, the
heater will restart automatically.
If the ON/OFF switch ever fails to illuminate when
switched to ON, check the fuse on the front panel of
the unit.
IMPORTANT: If the fuse is blown, replace
only with a similarly rated fuse. For 115 V use 5
Amp, 250 V, for 220 V use 2.5 Amp, 250 V.
STEAM
GENERATOR
Model TD-8556A
LOW WATER
ON
LOW
HIGH
1
2
3
4
5
6
7
8
OFF
250V
TYPE F
Vue de la page 0
1

Résumé du contenu

Page 1 - STEAM GENERATOR

Instruction Sheetfor the PASCOModel TD-8556ASTEAM GENERATOR012-04696D5/01$1.00IntroductionThe PASCO scientific Model TD-8556A Steam Genera-tor is an e

Commentaires sur ces manuels

Pas de commentaire